Pool tables are elegant designs for indoor sports rooms or patios. Most people play pool to as a way of spending leisure time with family or friends. When the tables are made from durable materials, they are able to last for over 20 years with very minimal maintenance. The felt is the most vulnerable part of the structure. When considering pool table refelting Denver residents have various things to consider.
The felt is that fabric that is attached to the table surface. When getting to re-felt, the first thing to do is determine the size of the table through the use of a measure tape. There is then replacement of the felt either at a home improvement depot or sports shop. During the purchase, there should be an extra 12 inches to its length and width. Since there are lots of color options, you will need to decide whether to use the same color or have a different one.
After the choice of color, the rails need to be removed using a crescent wrench. This is done by removing the bolts that attach the rails. Rails are also always covered by the felt and need to be re-felted too. This explains the need to buy extra material. Rails are carefully placed on the floor close to the table so that there is no mistake when reattaching them.
The felt to be replaced is removed by using a staple remover to pull out staples at the edge of the felt. It will be essential to ensure that all felt is removed from the top of the table. The old one can be placed on a thrash bag from where it can be disposed of later.
The new felt needs to be carefully placed while taking care to inspect that no damaged are done and that there are no stains. A sharp scissor should then be used to cut it, using the border of the table to guide you. Some felt is left over to be used to re-felt the rails.
After making the cut, a stapler is used to attach the felt to the top of the table. Stapling begins at the mid points of one end of the felt then proceeds to the left and right edges. When this is done, you proceed to the other end to pull the felt tightly. It then gets stapled like was done in the previous case.
The side edges will then need to be stapled. You should ascertain that the staples are at an equal distance from each other and lined up in the correct way. For the pockets, 3 slits should be cut on every pocket before wrapping and stapling the felt on the edges of the pockets. The felt is tightly pulled prior to stapling.
Finally, the structure is reassembled. Rails will be attached to their original positions using a crescent wrench. The pocket lines are inserted and the table is ready for use.
The felt is that fabric that is attached to the table surface. When getting to re-felt, the first thing to do is determine the size of the table through the use of a measure tape. There is then replacement of the felt either at a home improvement depot or sports shop. During the purchase, there should be an extra 12 inches to its length and width. Since there are lots of color options, you will need to decide whether to use the same color or have a different one.
After the choice of color, the rails need to be removed using a crescent wrench. This is done by removing the bolts that attach the rails. Rails are also always covered by the felt and need to be re-felted too. This explains the need to buy extra material. Rails are carefully placed on the floor close to the table so that there is no mistake when reattaching them.
The felt to be replaced is removed by using a staple remover to pull out staples at the edge of the felt. It will be essential to ensure that all felt is removed from the top of the table. The old one can be placed on a thrash bag from where it can be disposed of later.
The new felt needs to be carefully placed while taking care to inspect that no damaged are done and that there are no stains. A sharp scissor should then be used to cut it, using the border of the table to guide you. Some felt is left over to be used to re-felt the rails.
After making the cut, a stapler is used to attach the felt to the top of the table. Stapling begins at the mid points of one end of the felt then proceeds to the left and right edges. When this is done, you proceed to the other end to pull the felt tightly. It then gets stapled like was done in the previous case.
The side edges will then need to be stapled. You should ascertain that the staples are at an equal distance from each other and lined up in the correct way. For the pockets, 3 slits should be cut on every pocket before wrapping and stapling the felt on the edges of the pockets. The felt is tightly pulled prior to stapling.
Finally, the structure is reassembled. Rails will be attached to their original positions using a crescent wrench. The pocket lines are inserted and the table is ready for use.
About the Author:
You can visit www.anytimebilliards.com for more helpful information about The Procedure Of Pool Table Refelting Denver.
Aucun commentaire:
Enregistrer un commentaire